# KAWS test prints: what to print, how to test, what to tell me

These are cut straight from the final model (`KAWS_5ft_1524mm_v59_FINAL_straight.blend`), so they test the exact geometry of the big pieces.
Each test part uses the **same printer, nozzle and settings as the final part it stands in for** (everything on the 0.4 nozzle; either printer).
Filament: Bambu PLA Basic (black). Files: `FINAL_PRINT_FILES\TA1..TB4_*.gcode.3mf` (open in Bambu Studio, check the preview, print).

| Printer | Job | What | Time | Grams |
|---|---|---|---|---|
| A (0.4) | TA1 | T0 clearance pin + lock/hatch pins and heads + 6 joint pins | 0h51 | 18.8 |
| B (0.4) | TB1 | T0 clearance block | 0h19 | 13.5 |
| A (0.4) | TA2 | T1 lock: door top | 2h39 | 88.2 |
| B (0.4) | TB2 | T1 lock frame (body) | 2h48 | 127.8 |
| A (0.4) | TA3 | T2 hatch (the real hatch) + T3 key plate | 1h25 | 57.1 |
| B (0.4) | TB3 | T2 hatch floor (body) | 2h45 | 89.9 |
| A (0.4) | TA4 | T4 hinge: door bottom | 1h09 | 41.4 |
| B (0.4) | TB4 | T4 hinge sill (body) | 1h07 | 45.9 |

About 6.1 h on A and 7.0 h on B, 483 g in all. **Print TB1 + TA1 first** (an hour): the clearance answer can change every joint hole in the statue, and TA1 makes the pin heads you need for the two pauses below.

## Two plates need a pause (captive pin heads)
The lock-pin heads (8 mm) live in bores that are closed at the top and only 6.6 mm wide below, so a head can't be pushed in after printing. Drop the heads in during a pause:
1. Glue a 6x3 magnet into each head first (polarity per T3 below; mark the top of each head).
2. In Bambu Studio open the plate, go to Preview, drag the layer slider to the height below, right-click the + and choose **Add pause**, then Print.
   - **TB2 (T1 lock frame):** first layer above **20.9 mm**. This piece prints upside down, so at the pause drop one head into each of the two 8.6 mm bores **magnet end down** (on the statue the magnet must face up, toward the key spot), then resume. The printer then roofs the bores over the heads.
   - **TA3 (hatch):** first layer above **16.2 mm**. Drop one head into each of the hatch's two 8.6 mm bores, magnet end up, resume.
3. After printing, push each 6 mm shaft up through the bore from below and glue it to its head (a drop of CA on the shaft tip). The pin must slide freely afterwards.

Hardware you need for the tests: 4x 6x3 magnets (pin heads), 2x 12x3 magnets (key), 4x 6x2 magnets (2 door seat pairs) + 1 more 6x2 for the hatch reed trigger, 2 small springs (~5 OD x 10), 2 reed switches if you have them, a multimeter (continuity).

## T0: joint-pin clearance (block + pin, both 0.4)
Push the 8 mm test pin into each hole (labelled 05...30 = clearance per side in hundredths of a mm).
- Note the hole where the pin **slides in with light finger pressure** and the one that's **snug**.
- The joint holes are currently 0.15 per side. If your light-pressure hole is not "15", tell me the number; I re-cut every pin hole (it's one setting) and re-slice.
- Also try one of the 6 real joint pins (the D-shaped ones): same answer expected.

## T1: the door lock (frame + door top + lock pins)
Assemble: the heads are already captive (see the pause above); glue each shaft to its head from below. Stand the frame upright: the pins fall to the locked position. Put 6x2 seat magnets in the frame's upper seat pockets and the matching ones in the door (attracting).
Spring in each side-ledge pocket. Glue the two locating pins (cone out) into the side-ledge holes.
Hold the frame upright (as on the statue) and push the door top into the opening.

Check and report:
1. Pins drop and lock the door every time when it's pushed shut (the ramp lifts them and they fall in).
2. With the key held on the two key spots on the back skin above the opening: both pins lift **every time**. Wrong-way-round key (rotated 180 deg): pins stay down.
3. Pins drop back by themselves when the key is removed.
4. Locked: the door top sits flush and doesn't rattle. Unlocked: the springs push the top out 2-3 mm.
5. The locating cones centre the door so the hairline gap is even left to right.
6. Reed switch (if you have it) in the frame's reed seat: closes with the door shut, opens when the door top is out.

## T4: door hinge (sill + door bottom)
Hook the door bottom's tongue into the sill slot, tip it upright, tip it out again.
Check: it hooks without force, can't be pulled straight out when upright, and tips 15-20 deg without binding.

## T2: the hatch (real hatch + floor coupon + hatch pins)
Heads captive in the hatch (pause above), shafts glued on from below; a 6x2 trigger magnet in the hatch underside pocket; reed in the floor's reed seat.
Drop the hatch straight into its recess (v59 has no front tongue: it lifts straight out).
Check: pins fall into the floor holes and lock it; key on the hatch top lifts both pins; with the key still on, the hatch **lifts out on the key**; reed closes with the hatch in.
The hatch is the final part: if it passes, keep it.

## T3: the key (stand-in for the remote's base)
Two 12x3 magnets in pockets "1" and "2", pockets 50 mm apart, 0.8 mm skin on the flat face that touches the statue.
- Pocket 1 (the figure-right pin): magnet **N facing out** (toward the statue). Pin head under it: **S facing up**.
- Pocket 2 (the figure-left pin): magnet **S facing out**. Pin head under it: **N facing up**.
The same pairing applies to the hatch pins and, flipped, to the two 12x3 magnets in the cash-vault ceiling.

## What to send me
The T0 number, a pass/fail for each numbered check, and anything that felt tight or loose.
If the lock magnets are weak or the door doesn't pop, the fix is in the model (pocket depth, magnet size, spring pocket) and only touches the door-frame piece P30, the door, the hatch and the money piece P23.
