# KAWS 5 ft: what goes face-down, per piece

Every piece prints on a joint face (a flat cut face that gets glued and is never seen) unless noted. That gives a flat, accurate glue face, no support marks on the skin, and the part-ID (P01...) debossed on a joint face reads correctly.
Supports are set to come **from the build plate only**, so no support can grow inside a wire channel, a vault or a light pocket.

| ID | Piece | Face on the bed | Size on the bed, mm (w x d x h) | Support-needing overhang, cm² | Why |
|---|---|---|---|---|---|
| P01 | shoe toe, figure-right | its back joint face on the bed | 222 x 153 x 185 | 49 | same as P04 |
| P02 | shoe heel, figure-right | its front joint face on the bed | 229 x 159 x 217 | 58 | same as the toes |
| P03 | shoe heel, figure-left | its front joint face on the bed | 239 x 159 x 220 | 65 | same as the toes; flat sole stays a crisp vertical wall |
| P04 | shoe toe, figure-left | its back joint face on the bed | 234 x 159 x 184 | 56 | ballast chamber becomes vertical walls; supports for the chamber end grow from the plate through the open cut and are pulled out before gluing |
| P05 | lower leg + sock cuff, figure-right | its bottom joint face on the bed (prints the way it stands) | 185 x 183 x 157 | 3 |  |
| P06 | lower leg + sock cuff, figure-left | its bottom joint face on the bed (prints the way it stands) | 181 x 185 x 157 | 1 |  |
| P07 | upper leg, figure-right | its bottom joint face on the bed (prints the way it stands) | 144 x 142 x 155 | 1 |  |
| P08 | upper leg, figure-left | its bottom joint face on the bed (prints the way it stands) | 147 x 145 x 161 | 1 |  |
| P09 | shorts front, figure-right | upside down: its top joint face on the bed | 212 x 203 x 171 | 5 |  |
| P10 | shorts back, figure-right | its front joint face on the bed | 200 x 171 x 135 | 11 |  |
| P11 | shorts back, figure-left | its front joint face on the bed | 203 x 166 x 134 | 11 |  |
| P12 | shorts front, figure-left | upside down: its top joint face on the bed | 221 x 207 x 165 | 5 |  |
| P13 | belly side, figure-right | its front joint face on the bed | 84 x 168 x 163 | 0 |  |
| P14 | lower back corner, figure-right | its figure-left side joint face on the bed | 62 x 168 x 60 | 0 |  |
| P15 | belly front (figure-right) | its bottom joint face on the bed (prints the way it stands) | 118 x 190 x 168 | 0 |  |
| P16 | vault floor + lower vault + controller bay | its bottom joint face on the bed (prints the way it stands) | 163 x 228 x 168 | 40 | floor detail (hatch recess, pin holes, reed seat) prints upward; tree supports reach the lower-vault ceiling through its open bottom and come out through it |
| P17 | lower back (door sill, tongue slot) | its figure-right side joint face on the bed | 82 x 168 x 228 | 23 |  |
| P18 | belly front (figure-left) | its bottom joint face on the bed (prints the way it stands) | 126 x 188 x 168 | 0 |  |
| P19 | lower back corner, figure-left | its figure-right side joint face on the bed | 62 x 168 x 64 | 0 |  |
| P20 | belly side, figure-left | its back joint face on the bed | 89 x 168 x 163 | 0 |  |
| P21 | glove + cuff + money end, figure-left | its figure-right side joint face on the bed | 209 x 244 x 196 | 97 | on its money-cut face; supports land under the money and fingertips (sand after) |
| P22 | glove + money end, figure-right | the angled wrist joint face on the bed | 244 x 192 x 192 | 63 | least support; supports under the fingers |
| P23 | money centre ($ lights, band slot, lid seat, remote vault) | its figure-left side joint face on the bed | 152 x 228 x 190 | 35 | $ lights face sideways (straight walls); supports only at the stack's lower edge |
| P24 | glove cuff ring, figure-right | the angled wrist joint face on the bed | 134 x 134 x 77 | 28 |  |
| P25 | arm (upper arm to wrist), figure-right | the angled wrist joint face on the bed | 142 x 176 x 216 | 21 |  |
| P26 | arm (upper arm to wrist), figure-left | the angled wrist joint face on the bed | 161 x 148 x 225 | 16 |  |
| P27 | torso side, figure-right, back half | its figure-left side joint face on the bed | 238 x 173 x 94 | 1 | lies on its inner joint face (a 94 mm-tall print) instead of standing 238 mm tall on a narrow end |
| P28 | chest side front, figure-right | its figure-left side joint face on the bed | 81 x 197 x 63 | 1 |  |
| P29 | chest front (vault front wall) | its figure-left side joint face on the bed | 115 x 231 x 228 | 0 | the vault's flat ceiling would otherwise be an unsupportable 177 mm bridge |
| P30 | DOOR FRAME: back of the main vault (lock pins, springs, magnets) | upside down: its top joint face on the bed | 186 x 228 x 238 | 1 | keeps both lock-pin bores and the door jambs vertical (round, smooth bores for the gravity pins; true seams); the vault ceiling becomes a floor |
| P31 | chest side front, figure-left | its figure-right side joint face on the bed | 85 x 221 x 62 | 1 |  |
| P32 | torso side, figure-left, back half | its figure-right side joint face on the bed | 168 x 238 x 68 | 1 | lies on its inner joint face |
| P33 | shoulder + upper arm top, figure-right | its bottom joint face on the bed (prints the way it stands) | 119 x 112 x 132 | 0 |  |
| P34 | shoulder + upper arm top, figure-left | upside down: its top joint face on the bed | 123 x 115 x 118 | 0 |  |
| P35 | shoulder cap, figure-right | its bottom joint face on the bed (prints the way it stands) | 159 x 92 x 58 | 1 |  |
| P36 | neck base / upper chest | its bottom joint face on the bed (prints the way it stands) | 207 x 228 x 66 | 1 |  |
| P37 | shoulder cap, figure-left | its bottom joint face on the bed (prints the way it stands) | 157 x 93 x 62 | 1 |  |
| P38 | back of head, lower, figure-right | its figure-left side joint face on the bed | 168 x 152 x 198 | 0 |  |
| P39 | lower face + jaw, figure-right half (nostril) | upside down: its top joint face on the bed | 171 x 198 x 162 | 1 |  |
| P40 | lower face + jaw, figure-left half (nostril) | its back joint face on the bed | 162 x 179 x 169 | 1 |  |
| P41 | back of head, lower, figure-left | its figure-right side joint face on the bed | 168 x 152 x 179 | 0 |  |
| P42 | ear lobes, lower, figure-right | upside down: its top joint face on the bed | 136 x 137 x 218 | 0 |  |
| P43 | ear lobes, lower, figure-left | upside down: its top joint face on the bed | 152 x 141 x 228 | 0 |  |
| P44 | upper face, figure-right half (X eye) | its back joint face on the bed | 238 x 183 x 178 | 0 |  |
| P45 | back of head, upper, figure-right | its figure-left side joint face on the bed | 176 x 236 x 183 | 0 |  |
| P46 | upper face, figure-left half (X eye) | its back joint face on the bed | 237 x 163 x 176 | 0 |  |
| P47 | back of head, upper, figure-left | its front joint face on the bed | 163 x 236 x 176 | 0 |  |
| P48 | ear lobes, upper, figure-right | its bottom joint face on the bed (prints the way it stands) | 192 x 167 x 199 | 9 |  |
| P49 | ear lobes, upper, figure-left | its bottom joint face on the bed (prints the way it stands) | 166 x 189 x 193 | 12 |  |

Overhang = skin steeper than 55 deg from vertical that faces the plate (measured on the mesh). The slicer's measured support grams per plate are in PRINT_PLAN.md.

## Separate hardware parts

| Part | Face on the bed |
|---|---|
| Back door | inner (flat) face down; outer skin up |
| Lower vault hatch | bottom down, top face up |
| Controller bay door | top face down (magnet wells face up) |
| Cash lid + band underside | its inner (upper) face down; the visible underside faces up |
| Money band | its inner face down (U-shaped band, drops on from above) |
| Lock pins, hatch pins | shafts standing up (round for sliding in the bores); heads flat |
| Joint pins (D-pins) | lying on their flat side (strong across the joint) |
