# KAWS 5 ft: assembly guide (v59 straight, split v2)

49 statue pieces (P01-P49, the number is debossed on a hidden joint face of each), plus the separate hardware parts:
door, hatch, controller-bay door, cash lid + band underside, money band (U-shaped, drops on from above), lock/hatch/locating pins,
2 fill caps. The shorts buttons are part of the body now. See `PIECE_MAP.png` for where every piece goes and `ORIENTATION.md`
for which face each one prints on.

## Before the big print
1. Run the test prints (`tests\TEST_PRINTS.md`). The joint-pin clearance and the lock behaviour can still change the files.
2. Joint pins: 274 x (8 mm x 23 mm) D-pins + a few 4/5/6 mm ones, with ~10 % spares, on the PINS plates.
3. After printing: every pin hole and wire-channel mouth on the face a piece printed on is closed by a 0.5 mm skin (it stops support
   trees climbing into holes and tunnels). Twist an 8 mm drill bit by hand through each pin hole and poke each channel mouth open
   with a skewer. Run a rod or long bit through the channels listed in PRINT_QUEUE.md before gluing: those carry a thin support whisker.

## Printing notes
- Supports come from the build plate only, so nothing grows inside wire channels, vaults or light pockets.
  Sideways holes and channels have a small pointed top so the printer bridges them without support.
- **P30 (door frame) needs a pause** for the captive lock-pin heads: first layer above **14.9 mm** (it prints upside down).
  Drop both heads in **magnet end down**. Same for the **hatch**: first layer above **16.2 mm**, heads magnet end up.
  In Bambu Studio: Preview, drag the layer slider, right-click +, Add pause.
- Shoes (P01-P04): tree supports grow into the open ballast chamber to hold its end wall. Pull them out through the open joint face before gluing.
- P16: supports grow up inside the lower vault to its ceiling. Pull them out from below before gluing P16 onto the shorts.
- Gloves (P21, P22) and the money (P23) carry the only supports on visible skin: under the fingers and the stack's lower edge. Sand those spots.

## Glue and pins
- Dry-fit every joint with its pins first.
- Pins: a drop of thin CA in each hole. Faces: 2-part epoxy (or a gap-filling CA on small faces). Keep glue ~5 mm back from every
  wire-channel opening on the face, and clear any squeeze-out from the channel before it sets (a pipe cleaner works).
- **Shoes: the toe + heel joint (P01+P02, P03+P04) runs through the sealed ballast chamber.** Epoxy that whole face, so steel shot can't leak.
  Fill the shoes through the sole ports only after the statue is fully assembled and standing.

## Order
1. Shoes: P01+P02, P03+P04 (epoxy, sealed). Fill caps stay off until the end.
2. Legs: P05/P06 onto the shoes, then P07/P08.
3. Shorts ring: P09-P12, then onto the legs.
4. Belly/vault-floor ring: P16 (vault floor, lower vault, controller bay) first, then P17 (sill + tongue slot), P13-P15, P18-P20.
5. Main vault ring: P30 (door frame) first, onto P16/P17 on its stepped joint. Then P29 (chest front) and the torso sides P27, P28, P31, P32.
6. Shoulders: arm tops P33/P34, then the neck base P36 and shoulder caps P35/P37.
   The arm wiring arches over the arm-top joint (about 25 mm bend radius): feed a pull string through before gluing P33/P34.
7. Arms and hands: P25/P26 (arms) onto P33/P34, then P24 + P22 (right cuff ring, right glove) and P21 (left glove), then the money P23 between the gloves.
8. Head: build it as a unit (P38-P49) and dry-fit it on the neck base P36 before gluing.

## Wiring at the joints
Every channel stays a continuous tunnel across the joints (no pin is closer than 2.5 mm to any channel).
Pull each run in stages as you stack: feed a pull string through each piece before it goes on, then pull the wire bundle through.
Solder + heat-shrink or plug connectors at the joints is still your call.

## Joints (119)
| Joint | Glue area, cm² | Pins |
|---|---|---|
| P01 + P02 | 158 | 3 x d8 x 23 |
| P02 + P05 | 242 | 3 x d8 x 23 |
| P03 + P04 | 148 | 3 x d8 x 23 |
| P03 + P06 | 238 | 3 x d8 x 23 |
| P05 + P07 | 158 | 3 x d8 x 23 |
| P07 + P09 | 113 | 3 x d8 x 23 |
| P07 + P10 | 41 | 2 x d8 x 23 |
| P06 + P08 | 160 | 3 x d8 x 23 |
| P08 + P11 | 45 | 2 x d8 x 23 |
| P08 + P12 | 110 | 3 x d8 x 23 |
| P09 + P10 | 303 | 3 x d8 x 23 |
| P10 + P11 | 95 | 3 x d8 x 23 |
| P11 + P12 | 297 | 3 x d8 x 23 |
| P09 + P12 | 192 | 3 x d8 x 23 |
| P09 + P13 | 86 | 3 x d8 x 23 |
| P10 + P13 | 40 | 2 x d8 x 23 |
| P13 + P27 | 83 | 3 x d8 x 23 |
| P13 + P28 | 10 | 2 x d8 x 23 |
| P10 + P14 | 22 | 2 x d8 x 23 |
| P13 + P14 | 81 | 3 x d8 x 23 |
| P14 + P17 | 81 | 3 x d8 x 23 |
| P14 + P27 | 2 | 1 x d5 x 15 |
| P14 + P27 | 1 | glue only (thin contact strip) |
| P14 + P27 | 1 | glue only (thin contact strip) |
| P09 + P15 | 149 | 3 x d8 x 23 |
| P12 + P15 | 5 | glue only (thin contact strip) |
| P13 + P15 | 115 | 3 x d8 x 23 |
| P15 + P28 | 21 | 2 x d8 x 23 |
| P15 + P29 | 99 | 3 x d8 x 23 |
| P09 + P16 | 116 | 3 x d8 x 23 |
| P10 + P16 | 15 | 2 x d8 x 23 |
| P11 + P16 | 15 | 2 x d8 x 23 |
| P12 + P16 | 118 | 3 x d8 x 23 |
| P13 + P16 | 274 | 3 x d8 x 23 |
| P15 + P16 | 194 | 3 x d8 x 23 |
| P16 + P18 | 189 | 3 x d8 x 23 |
| P16 + P20 | 273 | 3 x d8 x 23 |
| P16 + P29 | 21 | 2 x d8 x 23 |
| P16 + P30 | 73 | 3 x d8 x 23 |
| P10 + P17 | 56 | 2 x d8 x 23 |
| P11 + P17 | 53 | 2 x d8 x 23 |
| P16 + P17 | 139 | 3 x d8 x 23 |
| P17 + P30 | 8 | 2 x d6 x 19 |
| P17 + P30 | 5 | 1 x d5 x 15 |
| P17 + P30 | 3 | glue only (thin contact strip) |
| P12 + P18 | 147 | 3 x d8 x 23 |
| P15 + P18 | 185 | 3 x d8 x 23 |
| P18 + P20 | 116 | 3 x d8 x 23 |
| P18 + P29 | 102 | 3 x d8 x 23 |
| P18 + P31 | 23 | 2 x d8 x 23 |
| P11 + P19 | 21 | 2 x d8 x 23 |
| P17 + P19 | 82 | 3 x d8 x 23 |
| P19 + P20 | 90 | 3 x d8 x 23 |
| P19 + P32 | 2 | glue only (thin contact strip) |
| P19 + P32 | 1 | glue only (thin contact strip) |
| P19 + P32 | 1 | glue only (thin contact strip) |
| P11 + P20 | 43 | 2 x d8 x 23 |
| P12 + P20 | 91 | 3 x d8 x 23 |
| P20 + P31 | 10 | 2 x d8 x 23 |
| P20 + P32 | 84 | 3 x d8 x 23 |
| P21 + P23 | 146 | 3 x d8 x 23 |
| P22 + P23 | 153 | 3 x d8 x 23 |
| P22 + P24 | 82 | 3 x d8 x 23 |
| P24 + P25 | 43 | 2 x d8 x 23 |
| P21 + P26 | 54 | 2 x d8 x 23 |
| P27 + P28 | 60 | 2 x d8 x 23 |
| P27 + P30 | 362 | 3 x d8 x 23 |
| P28 + P29 | 72 | 3 x d8 x 23 |
| P29 + P30 | 177 | 3 x d8 x 23 |
| P29 + P31 | 84 | 3 x d8 x 23 |
| P30 + P32 | 353 | 3 x d8 x 23 |
| P31 + P32 | 63 | 2 x d8 x 23 |
| P27 + P33 | 108 | 3 x d8 x 23 |
| P32 + P34 | 102 | 3 x d8 x 23 |
| P27 + P35 | 94 | 3 x d8 x 23 |
| P35 + P38 | 17 | 2 x d4 x 13 |
| P35 + P39 | 3 | glue only (thin contact strip) |
| P29 + P36 | 31 | 2 x d8 x 23 |
| P30 + P36 | 407 | 3 x d8 x 23 |
| P35 + P36 | 67 | 2 x d8 x 23 |
| P36 + P37 | 72 | 3 x d8 x 23 |
| P36 + P38 | 120 | 3 x d8 x 23 |
| P36 + P39 | 62 | 2 x d8 x 23 |
| P36 + P40 | 43 | 2 x d8 x 23 |
| P36 + P41 | 83 | 3 x d8 x 23 |
| P32 + P37 | 43 | 2 x d8 x 23 |
| P34 + P37 | 58 | 2 x d8 x 23 |
| P37 + P40 | 5 | glue only (thin contact strip) |
| P37 + P41 | 14 | 2 x d4 x 13 |
| P38 + P39 | 253 | 3 x d8 x 23 |
| P38 + P42 | 41 | 2 x d8 x 23 |
| P39 + P40 | 209 | 3 x d8 x 23 |
| P38 + P41 | 179 | 3 x d8 x 23 |
| P40 + P41 | 228 | 3 x d8 x 23 |
| P41 + P43 | 67 | 2 x d8 x 23 |
| P39 + P42 | 69 | 2 x d8 x 23 |
| P42 + P44 | 44 | 2 x d8 x 23 |
| P40 + P43 | 64 | 2 x d8 x 23 |
| P43 + P46 | 36 | 2 x d8 x 23 |
| P39 + P44 | 251 | 3 x d8 x 23 |
| P38 + P45 | 233 | 3 x d8 x 23 |
| P42 + P45 | 23 | 2 x d8 x 23 |
| P44 + P45 | 360 | 3 x d8 x 23 |
| P45 + P48 | 21 | 2 x d8 x 23 |
| P45 + P48 | 18 | 2 x d8 x 23 |
| P40 + P46 | 212 | 3 x d8 x 23 |
| P44 + P46 | 362 | 3 x d8 x 23 |
| P41 + P47 | 202 | 3 x d8 x 23 |
| P43 + P47 | 31 | 2 x d8 x 23 |
| P45 + P47 | 342 | 3 x d8 x 23 |
| P46 + P47 | 316 | 3 x d8 x 23 |
| P47 + P49 | 24 | 2 x d8 x 23 |
| P47 + P49 | 14 | 2 x d8 x 23 |
| P42 + P48 | 157 | 3 x d8 x 23 |
| P44 + P48 | 41 | 2 x d8 x 23 |
| P44 + P48 | 38 | 2 x d8 x 23 |
| P43 + P49 | 178 | 3 x d8 x 23 |
| P46 + P49 | 38 | 2 x d8 x 23 |
| P46 + P49 | 30 | 2 x d8 x 23 |
