# KAWS Moneymaker — v4 print & assembly guide (v4.3)

v4.3: the shoulders now use the OFFICIAL Companion shoulder shape (taken from the original model's body, which the
torso was cut from) and ease into the bent concept arm below - rounded dome shoulders like the real figure instead
of squared-off ones. Reprint torso_L / torso_R / upperarm_L / upperarm_R if you printed them before v4.3.

v4.2 fixes: the money leg in his right hand is now cut off right where it enters the fist (no green poking
out below the thumb), the whole arm-to-torso joint is now one smooth rounded blend from the top of the
shoulder down into the armpit (no grooves, slits or gaps - no clay needed), and each arm now has **two glued pegs** into the torso
(the big shoulder peg + a smaller lower peg that stops the arm twisting while the glue sets).

v4.1 fixes: money leg no longer runs out the back of the right fist (trimmed to match the flipped half),
the carved line from the left nostril down the chest is gone (light channel re-routed inside), and the
armpits now blend into the torso with a smooth rounded fillet.

v4 = concept arms copied from the shoulder (natural elbows), concept gloves with lit X's, the concept's
riffled money stack with a glowing band + glowing border/"100" lines, and one big lit back compartment
(big magnetic back door with a nested remote hatch). Everything prints **black** except the parts that
glow, which print **translucent**.

Every file below was checked before release: zero overlap with every other part (exact solid math),
fits the 256mm bed, watertight, and the LED wire path was traced end-to-end through the real geometry.

## What you already have (keep)
- Feet: part_1, part_19, part_17, part_71, heel_R — printed, unchanged
- pelvis_back (its small stash + door still works as a bonus), pelvis_front — unchanged
- Head: head_lowR (printed) + part_13, part_23, face_top, skull_ear_RB, part_15, part_49, part_53 — unchanged
- **part_11 (face lower-left) — use the NEW file** (v4.1): the old light-wire channel broke through the skin
  beside the left nostril and down the chest; the skin is restored and the wire now runs deeper inside
- Translucent eye / nose / shoe inserts — unchanged

## Scrap / do NOT print
- leg_glove_L, leg_glove_R (printed) → scrap (old thigh gloves)
- body_L, body_R (printed, old vault version) → scrap, replaced by torso_L / torso_R
- arm_L, arm_R, vault_door_body_L/R, vault_shelf_x2, vault_service_cap, insert_glove41/43,
  money_stack, money_band (old), money_bill_x3 → obsolete

## New prints (v4)  —  open the .3mf → Slice → Print (settings baked in)
Times/filament are from Bambu Studio's own slicer on these exact files.

| Group | File (console id) | What | Colour | Time | Filament |
|---|---|---|---|---|---|
| Test first | `coupon_money` | Money corner — border + "100" | black + translucent | 2h 8m 38s | 31 g |
| Test first | `coupon_glove_x` | Glove X patch | black | 1h 30m 49s | 17 g |
| Test first | `coupon_xinsert` | Glove X insert | translucent | 1h 18m 27s | 31 g |
| Head | `part_11` | Face lower-left (v4.1 restored skin) | black | 7h 52m 0s | 226 g |
| Hips + legs | `flank_L` | Left hip side | black | 1h 54m 21s | 73 g |
| Hips + legs | `flank_R` | Right hip side | black | 1h 40m 11s | 67 g |
| Hips + legs | `leg_L` | Left leg (plain) | black | 3h 15m 45s | 110 g |
| Hips + legs | `leg_R` | Right leg (plain) | black | 3h 39m 41s | 118 g |
| Torso | `torso_L` | torso_L — left half + compartment | black | 10h 52m 34s | 335 g |
| Torso | `torso_R` | torso_R — right half + compartment | black | 11h 6m 29s | 344 g |
| Torso | `back_door` | Back door | black | 4h 6m 28s | 104 g |
| Torso | `remote_hatch` | Remote hatch | black | 51m 10s | 18 g |
| Arms | `upperarm_L` | Upper arm left | black | 3h 19m 58s | 83 g |
| Arms | `upperarm_R` | Upper arm right | black | 3h 34m 5s | 88 g |
| Arms | `forearm_L` | Forearm left | black | 2h 8m 1s | 62 g |
| Arms | `forearm_R` | Forearm right | black | 2h 57m 18s | 73 g |
| Arms | `glove_L` | Glove left | black | 9h 31m 1s | 174 g |
| Arms | `glove_R` | Glove right | black | 9h 26m 37s | 183 g |
| Arms | `xinsert_L` | Glove X insert left | translucent | 1h 9m 44s | 29 g |
| Arms | `xinsert_R` | Glove X insert right | translucent | 1h 13m 53s | 29 g |
| Money | `money_stub` | Money stub | black + translucent | 8h 11m 23s | 129 g |
| Money | `money_arch` | Money arch + flipped bills | black + translucent | 14h 11m 18s | 238 g |
| Money | `money_band` | Money band | translucent | 4h 25m 43s | 75 g |
| **Total** | | | | **~110 h** | **~2.64 kg** |

Colours: **black** = any black slot. **Translucent** = your translucent roll. The two money bills are
2-colour prints: they're set up with filament 1 = black and filament 4 = translucent — when you hit
Print, make sure the AMS mapping puts filament 4 on the translucent slot.

## Do these two test prints FIRST (~1 hour total)
1. **coupon_money** (black + translucent, ~30 min): one corner of a bill with its border line and a "100".
   Check: lines come out crisp, translucent is fused to the black, and a phone flashlight behind it glows.
2. **coupon_glove_x + coupon_xinsert** (~40 min): a patch of glove with the X slot + the matching
   translucent X. Check: the X pushes in with light finger pressure (not loose, not forced).
   If it's too tight/loose, tell Claude the result — the clearance is one number to change.

## Hardware to add to the shopping list
- USB fairy light string **#4**, 3m, warm white (for compartment → arm → gloves → money)
- USB splitter (if your RF dimmer only takes one plug)
- 6x2mm magnets: 12 more (door 4 pairs, hatch 2 pairs)
- Optional: 1 NC reed switch (seat is molded in the upper-right door ledge)

## Painting (before any lights/inserts are glued)
- Figure: black / hydro-dip as planned. **Mask the door + hatch hairlines** (dip with door installed, then
  score the hairline like before).
- Money bills: paint green **right over the raised translucent lines**, then lightly sand only the
  line tops (400 grit on a flat stick) until the clear lines show again. Don't paint the band.
- Arm-to-torso seam: the blend is printed in, so only the thin glue line remains - wipe a little Bondo spot putty
  into that line before priming and sand flush.
- Glove X inserts, band: leave unpainted (clear coat is fine). Glue the X's in AFTER painting.

## Assembly order (thread the lights as you go — the string can't be added after glue-up)
1. Legs onto ankles (glue gap 0.2mm), flanks onto the pelvis sides, pelvis onto legs.
2. Torso halves (torso_L + torso_R) glued together, then onto the pelvis/flanks.
3. Magnets: 4 in the door ledges + 4 in the door (check polarity!), 2 + 2 for the remote hatch.
4. **Light string #4**: USB end goes down the chase to the heel exit with the others; feed the tip from the
   chase port into the compartment, leave a loop for compartment light, then into the LEFT shoulder port.
5. Upper arm L: thread the string through its shoulder peg + bore. Dry-fit both pegs (shoulder + lower) first,
   then glue both pegs AND the flat contact face (CA gel or 2-part epoxy), hold/tape 10 min.
   Same for the right upper arm (no string on the right arm).
6. Forearms: thread through the elbow tenon, glue tenon into the forearm socket.
7. Gloves: thread through the wrist peg into the glove, out the palm hole. Glue gloves onto wrists.
8. Money: string goes into the stub through the hidden hole in the left fist, through the band tunnel,
   through the arch, and out the arch's hole into the RIGHT fist (tip ends in the right glove, lighting
   its X). Glue stub + band + arch together, then press the money into both fists and glue.
9. Head on last (as before).
