# KAWS Companion 1.2m — v2 (consolidated, 22 pieces)

**This supersedes v1.** Same verified figure (1207mm, official proportions, all light mods),
now merged from 36 into 22 pieces: ~1kg less filament, ~13 fewer glue seams (including the
face center seam, the inner-thigh crevice, and the floating gloves — now printed attached),
and the legs now seat flush on the ankles (0.2mm glue gap, was a 2.5mm standoff).

Verified: 0.0000% interference across the assembly, every piece watertight, every piece
fits the 256mm plate, all light channels intact.

## Files
- `v2/*.stl` — the 22 pieces, pre-oriented flat-face-down. Import 3–5 at a time into Bambu
  Studio, auto-arrange, slice. (The old kaws_slim_lights.3mf is v1 — don't mix versions.)
- Inserts + money parts: unchanged from the v1 kit zip (still compatible).

## Slicer settings (all pieces)
- 0.2mm layer (or 0.28 draft — everything gets sanded), 2 walls
- **Sparse infill: 4% LIGHTNING** (not grid, not 0% — lightning supports the flat top faces
  with near-zero material and lets LED light through)
- Top 3 / bottom 2 shell layers
- Brim only on tall skinny pieces (skull_ear_RB, part_15); textured plate otherwise bare
- Filament: your black matte PLA everywhere; translucent clear for inserts + money band

## AMS setup (so you never babysit a runout)
Load 3 slots with black, set each slot to the same profile (PLA, black), enable
**Auto-refill**. The AMS hot-swaps slots mid-print with no pause. Largest piece is ~425g,
so 3 loaded spools is 7x margin.

## Piece map (22)
Merged: body_R (3+9), body_L (5+7), face_top (21+47), head_lowR (35+39+63+65),
pelvis_back (29+31), pelvis_front (33+37), arm_R (55+57), arm_L (51+59),
leg_glove_R (27+41), leg_glove_L (25+43), heel_R (67+69), skull_ear_RB (45+61).
Unchanged: part_11, part_13, part_15, part_23, part_49, part_53, part_1, part_17,
part_19, part_71.

## Hidden vault system (built into pelvis_back, body_L, body_R)
Three concealed compartments behind flush magnetic doors on the figure's back. The door
hairlines vanish under the marble dip. Total capacity ~111 banded stacks of 50 x $20 (~$111k).

- **Pelvis hatch (decoy layer):** opens to a shallow bay for the LED remote (cradle piece
  comes later, sized to your remote). Pull the magnetic false panel behind it -> small stash
  (~7 stacks on edge). Anyone who finds this hatch thinks they found everything.
- **Torso vaults (the real ones):** one per body half, ~52 stacks each stored standing,
  two tiers (use the vault_shelf plates between tiers). Insert stacks tilted, stand them up.
- **Doors (fully featureless — no visible opening mechanism):** print vault_door_* in black.
  Each seats on 4 magnet pairs. Opening = the MAGNET KEY: each door has two magnet wells
  buried 1.8mm under its outer skin near the top edge. Drop 2-3 stacked 6x2 magnets down
  each well and glue (check polarity: they must ATTRACT your key magnet). Sweep a strong
  neodymium key magnet (a 20x5mm N52 disc is ideal) over the back to find the door, then
  peel from the top edge. Park the key inside the heel USB recess.
  BEFORE printing the first vault piece: print the door test coupon (ask Claude) — a small
  frame corner + door section to tune magnet counts so the key wins the peel but the door
  still seats firmly. (A suction phone-puller works as a silent emergency backup.)
- **CRITICAL FINISHING STEP for invisibility:** hydro dip with the doors INSTALLED (mask the
  gaps from behind with tape) so the marble pattern flows unbroken across the hairlines. After
  clear coat, score along each hairline with a fresh blade before first opening so the paint
  film parts cleanly instead of chipping.
- **Door-activated lighting:** each vault frame has a reed-switch seat next to the top-right
  magnet block. Wire a NORMALLY-CLOSED reed switch in series with a few LEDs in that vault:
  door closed = dark (no glow through the hairline), door open = cash lights up.
- **Service access:** body_L vault has a capped 26mm port into the body cavity — future you
  can replace dead LED strings through it instead of cracking glue joints. body_R has a wire
  pass; the pelvis vault connects up to body_L via a hidden riser channel.

**Extra shopping:** ~20x 6x2mm neodymium magnets (doors, panel; glue with CA, check polarity
twice before gluing), 3x normally-closed reed switches, silica gel packs for the vaults.

## Assembly (bottom-up, thread lights before gluing each joint)
1. Feet: part_1 + part_19 (left), heel_R + part_71 + part_17 (right). USB cable in through
   the left heel hole first.
2. Legs: leg_glove_L / leg_glove_R onto ankles (gloves come attached; 0.2mm glue gap at
   the ankle joint — epoxy or gap-filling CA).
3. Pelvis: pelvis_front + pelvis_back around the wire runs, onto the legs.
4. Body: body_L + body_R.
5. Head: part_11 + part_13 + head_lowR + part_53, then face_top + part_23 + skull_ear_RB +
   part_15 + part_49. Spray interiors flat white before closing (black filament absorbs
   light — white bounce roughly doubles the eye glow). Coil a generous LED cluster behind
   the eyes/nose.
6. Fill seams, sand, prime, hydro dip. Glue translucent inserts in LAST, after paint.
7. Money stack: band on, bills fanned and glued, LED through the boss, press into glove.
